Audi 80/90/Coupe

Since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburettors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Ignition system
- 8. Transmission
   8.1.2. A plug - the main cylinder of coupling
   8.1.3. Press a coupling disk
   8.1.4. Malfunctions of coupling
   + 8.2. A mechanical transmission 012
   - 8.3. A mechanical transmission 01А
      8.3.2. Removal and transmission installation
      8.3.3. Dismantling and transmission assemblage
      - 8.3.4. Differential
         8.3.4.2. Differential mechanisms
         8.3.4.3. Removal and differential installation
         8.3.4.4. Dismantling and differential assemblage
      8.3.5. A kardannyj shaft
      8.3.6. Central карданный the hinge
   + 8.4. An automatic transmission 089
   + 8.5. An automatic transmission 087
   8.6. Dismantling and assemblage of automatic transmissions
   8.7. The block of valves
   + 8.8. An automatic transmission 097
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. A steering
+ 12. A body, salon
+ 13. A central air
+ 14. An electric equipment


32ad0625

8.3.4.2. Differential mechanisms
THE GENERAL DATA

The mechanism of forward differential

1. Carter of the main transfer
2. An internal holder of a small roller bearing
Establish by means of tool VW 519
3. A differential box
At replacement of a box of differential adjust installation of a gear wreath
4. Gear wheels of semiaxes
5. A pin of an axis of satellites
Remove with the help выколотки
6. An axis of satellites
Remove with the help выколотки after removal of a pin of an axis of satellites
7. Satellites
8. A persistent washer
Before installation grease трансмиссионным with oil
9. A bolt of fastening of a gear wreath
Use bolts only the demanded specification
Tighten in regular intervals in a diagonal order to 90 Н.м.
10. A gear wheel of a drive of a speedometer
For an electronic speedometer
11. A cover картера the main transfer
12. Adjusting washer S1
Note a thickness
13. An external holder of the big conic roller bearing
Establish by means of tool VW 295 and VW 511
14. An internal holder of the big conic roller bearing
Establish by means of the tool 3118
15. A gear wreath
The gear wreath and leading gear wheel are adjusted to each other
At pair replacement a gear wreath / a leading gear wheel spend adjustment
Remove from differential with the help выколотки
Installation: heat up to 100Р°С and establish, using centering pins as the directing
16. An external holder of a small roller bearing
Establish by means of the tool 2050 and VW 295
17. Washer S2
Note a thickness

Back differential

1. The synchronizer
2. The locking plug
3. Муфта couplings of blocking of differential
4. A differential box
5. A cover of the main transfer
6. A leading gear wheel
7. Carter of the main transfer
8. A switching plug

The differential mechanism

1. 25 Н.м.
2. A semiaxis flange
3. A washer
Define a necessary thickness
4. An epiploon
5. Муфта couplings (differential blocking)
6. A washer
7. Сапун
8. Carter of the main transfer (with a leading gear wheel)
9. Washer S2
Note a thickness
10. The semiaxis bearing (an external holder)
11. Заглушка a drain aperture 25 Н.м.
12. A differential box
13. The semiaxis bearing (an external holder)
14. Washer S1
Note a thickness
15. A clip
Always replace
16. A magnet
17. A cover
герметизируйте by means of hermetic AMW 188
18. 25 Н.м.
19. An epiploon
Remove by means of the lever
Establish against the stop
20. Заглушка a jellied aperture 25 Н.м.
21. A semiaxis flange