|
Adjustment of installation of wheels
It is recommended to inspect adjustment of wheels after at least 1000–1200 km of run when suspension bracket springs had time to enter into a normal operating mode.
For check it is necessary:
– Exact adjustment of the measuring equipment;
– That the weight of the car at check carrying out equaled only to its own weight with the filled tank and the established equipment;
– That pressure in tyres equaled to the standard;
– That the car has been located on an equal surface, also before carrying out of check the car is necessary for rocking some times to establish a suspension bracket;
– That there was no excessive free wheeling in the steering mechanism;
– Check up a suspension bracket on presence of an excessive free wheeling and damages.
Cars with a forward drive
Forward wheels
|
Rating values
|
| Convergence of forward wheels (on wheels there is no pressure) |
+10 ' ± 10'
|
| Disorder of forward wheels |
Wheels stand directly
|
-45 ' ± 30'
|
The maximum admissible distinction between the left and right wheel
|
30'
|
Difference in convergence coal between left and right wheels
|
-55 ' ± 30'
|
| Corner of a longitudinal inclination шкворня |
It is not regulated
|
+1°15 ' ± 30'
|
The maximum admissible distinction between the left and right wheel
|
30'
|
Back wheels
|
Rating values
|
| Disorder of back wheels |
It is not regulated
|
-1 ' ± 20'
|
The maximum admissible distinction between the left and right wheel
|
30'
|
| Convergence of back wheels |
It is not regulated
|
+20 ' ± 20'
|
The maximum admissible distinction between the left and right wheel
|
25'
|
Cars with a full drive, and also with 20 клапанными engines
Forward wheels
|
Sedan
|
Compartment
|
| Convergence of forward wheels (on wheels there is no pressure) |
+10 ' ± 10'
|
+10 ' ± 10'
|
| Disorder of forward wheels |
Wheels stand directly
|
-50 ' ± 30'
|
-50 ' ± 30'
|
The maximum admissible distinction between the left and right wheel
|
30'
|
30'
|
| Difference in convergence coal between left and right wheels at turn of wheels on 20 ° |
-1 ' ±30'
|
-1 ' ±30'
|
| Corner of a longitudinal inclination шкворня |
It is not regulated
|
+1°25 ' ± 30'
|
+2°15 ' ± 30'
|
The maximum admissible distinction between the left and right wheel
|
30'
|
30'
|
Back wheels
|
Sedan
|
Compartment
|
Disorder of back wheels
|
-45 ' ± 30'
|
-45 ' ± 30'
|
The maximum admissible distinction between the left and right wheel
|
30'
|
30'
|
Convergence of back wheels
|
+20 ' ± 10'
|
+20 ' ± 10'
|
Convergence corner on one wheel
|
+10 ' ± 5'
|
+10 ' ± 5'
|
Definition / adjustment of a corner of a convergence of back wheels (for cars with a forward drive)
1. If a corner of a convergence of both wheels positive (+ / +) or negative (-/-), subtract smaller value from большего and divide on 2.
2. If a corner of a convergence of one wheel positive, and the second negative (+/-), combine both values and divide on 2.
Disorder of forward wheels, adjustment (for cars with the spherical hinges of a forward suspension bracket fastening in 2 points)
| PERFORMANCE ORDER |
|
1) ослабьте both nuts of fastening of the spherical hinge to the suspension bracket lever (are specified by arrows) |
| 2) move the spherical hinge by means of the lever and adjust a corner of disorder of forward wheels |
| 3) tighten nuts of fastening to 65 Н.м. |
| 4) repeatedly check up a corner of disorder of wheels and adjust it if it is necessary |
| 5) check up a corner of a convergence of wheels, adjust it if it is necessary |
|
|
