Audi 80/90/Coupe

Since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburettors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Ignition system
- 8. Transmission
   8.1.2. A plug - the main cylinder of coupling
   8.1.3. Press a coupling disk
   8.1.4. Malfunctions of coupling
   - 8.2. A mechanical transmission 012
      8.2.2. The lever mechanism of the lever of a gear change
      8.2.3. Removal and transmission installation
      8.2.4. Differential mechanisms
   + 8.3. A mechanical transmission 01А
   + 8.4. An automatic transmission 089
   + 8.5. An automatic transmission 087
   8.6. Dismantling and assemblage of automatic transmissions
   8.7. The block of valves
   + 8.8. An automatic transmission 097
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. A steering
+ 12. A body, salon
+ 13. A central air
+ 14. An electric equipment


32ad0625

8.2.2. The lever mechanism of the lever of a gear change
THE GENERAL DATA

The gear change lever in gathering

1. The gear change lever
Can be inserted into a spherical support only in one position
2. A lock ring
Always replace
The roundish party should be turned to a spherical support
Remove before removal of a spherical support
3. 25 Н.
4. A lamellar spring
5. A side scene
6. Draught of a gear change
Colour code: blue = for engines with 5 cylinders
7. A cover
8. A clip
9. 25 Н.м.
10. 20 Н.м.
Always replace
The screw is greased by hermetic
11. The basis of the lever of a gear change
Fastens on a floor by means of hermetic AKD 512 001
12. 10 Н.м.
13. A switching plug
14. 10 Н.м.

15. A directing cup
It is necessary to establish restrictions for movement of a spherical support at the left and on the right
Emphasis establish so that at inclusion of transfer of a backing the lever has been inclined to the left
16. A spherical support
Establish a spring and the plug in a spherical support, and then establish the gear change lever so that the spring and the plug were on the correct party in a moving direction
Establish a spherical support before installation стопрного rings
17. The plug
The roundish end is turned to the gear change lever
18. A spring
19. An axis of the lever of a gear change
20. The raspornaja plug
21. A lock ring.
22. A cover
For removal unscrew the screw
23. The screw
24. The handle

The prevention

Do not grease the lever mechanism of the lever of a gear change.


Adjustment

PERFORMANCE ORDER
1) move the gear change lever to neutral position
2) remove the lever handle, unscrew the screw of fastening of a cover of the lever and remove a cover
3) ослабьте a bolt (it is specified by an arrow)
4) establish the gear change lever vertically (as far as possible)

Check

PERFORMANCE ORDER
1) establish the gear change lever so that both uvulas on a spherical support were on identical distance "a" (it is specified by arrows) from a directing cup
2) tighten a bolt and check up, that the lever did not move
3) check up work of the mechanism of a gear change, include all transfers by turns
4) 3-ja/4th transfers should be in the same plane, as neutral
5) check up work of a safety latch of transfer of a backing. If it does not work, turn off screws and turn directing cup a little
6) establish a cover and the handle of the lever of a gear change