Audi 80/90/Coupe

Since 1986-1991 of release

Repair and car operation

12.13. Window condensing stoppers, a window regulator

THE GENERAL DATA

Window frame in assemblage

1. A bolt with шестигранной a head крепит a bearing element to a door frame 2. A window sealant 3. A window regulator Remove only when the bearing element of a door is removed 4. An overlay 5. A clamp for a rope of a regulator of a window 6. Door glass Remove only when the bearing element of a door is removed

7. A lock washer 8. A washer 9. A prokladochnoe ring 10. The shock-absorber 11. A bolt with шестигранной a head 6 Н.м. 12. Заглушка 13. A cover of the internal lock of a door 14. A bearing element of making elements of a door 15. A door frame

Window regulator in assemblage

1. A condensing lining of door glass 2. A lock washer 3. A washer 4. The amortisation plug 5. Door glass Remove bearing element of a door 6. A window regulator Remove together with a bearing element of a door

7. A cover of the lock of a door 8. A fixing pin 9. A bolt with шестигранной a head for doorframe fastening 10. A shestigrannaja nut 6 Н.м. 11. A plate of the holder 12. A door frame 13. A condensing lining

Condensing stoppers

Insert from below in directing windows And = 65 mm It is measured from the end of a groove of a window

The stopper is used as a sealant, and also antinoise means.

Window regulator

Removal

PERFORMANCE ORDER

1) remove bearing element of components of a door 2) remove a lock washer 2 3) remove an assembly washer and a protective material 4) pull out a window from a shutter of the elevating mechanism of a window 5) unbend a clip 7 in a direction of an arrow and pull out a rope from a clip 6) unscrew bolts with шестигранной a head 6 7) unscrew bolts with шестигранной a head 16

Installation

Installation carry out upside-down, in view of the following:

PERFORMANCE ORDER

1) screw up bolts with шестигранной a head 6 Н.м. 2) place shock-absorbers between a window and a bearing element 3) check up a window and if necessary adjust it

Window frame in assemblage (Compartment model)

1. The screw, 20 Н.м. 2. An aluminium clamping overlay 3. A clip, external 4. A clip, internal 5. Door glass 6. An adjusting clamp 7. A window regulator 8. A butt overlay 9. The screw, 20 Н.м.

10. The buffer 11. An arm 12. A nut, 6 Н.м. 13. A bolt, 15 Н.м. 14. An adjusting washer Establish, as it is required 15. A bolt, 15 Н.м. 16. A flat nut / a washer, 15 Н.м.

Window regulator, removal / installation (Compartment model)

---

The prevention

The site of intermediate rings should be noted before removal of a regulator of a window.

---

Removal

PERFORMANCE ORDER

1) remove the decorative panel of a door 2) note a site of four top bolts of a regulator of a window (an arrow 3) ослабьте the bottom bolts of a regulator of a window (an arrow 4) remove intermediate rings 5) unscrew all six bolts of a regulator of a window 6) remove a regulator of a window from a door

Installation

PERFORMANCE ORDER

1) paste sticky strips, as is shown in drawing, on a window Pencil note the size and = 20 mm 2) establish a window regulator in a door covering 3) insert draught of the lock with the door-lock button 4) establish into place all bolts of a regulator of a window and tighten manually 5) pay attention to the marks made round the top bolts 6) close a door and check up the sizes: b = 19.5 – 21.00 mm With = 12.0 – 15.0 mm The prevention If the sizes do not correspond specified, move a window regulator in a door covering while the sizes will not coincide with the specified. Rough pressure of glass in the field of the central rack of a body or discrepancy of the sizes b and with the demanded can cause noise from a wind or a leak. 7) place intermediate rings under bolts 8) close a door and check up pressure of glass upon a door; the door should be closed easily

Window regulator, check (Compartment model)

PERFORMANCE ORDER

1) open a door 2) with a chalk rub edge of glass which touches the central rack of a body 3) close and again open a door 4) check up a print left a chalk on the condensing lining of a window 5) if a print is on all length of a condensing lining, door glass is established correctly; if is not present: add or clean intermediate rings, and then anew carry out check 6) close a door and a window 7) place a metal ruler outside how it is shown in drawing And = 17 – 18 mm To reach the size and, the butt overlay can be adjusted 8) establish the decorative panel of a door 9) check up the car on noise from a wind and a leak

Window regulator, adjustment (Compartment model)

---

The prevention

The covering of a window and door is necessary for regulating first of all.

---

PERFORMANCE ORDER

1) ослабьте bolts (arrows) 2) close a door 3) two experts further be required; slightly press on bearing element in a direction opposite to a roof and a rack 4) will apply slightly more forces, than it is necessary. The rubber lining will retur