Audi 80/90/Coupe

Since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburettors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Ignition system
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. A steering
- 12. A body, salon
   12.2. The central section of a guard
   12.3. A cowl rope
   12.4. A forward guard
   12.5. A forward wing
   12.6. Lock pins of a cowl, the rubber shock-absorber
   12.7. A cowl
   12.8. A gazonapolnennaja rack (models the Sedan)
   12.9. A luggage carrier cover
   12.10. A back door (Compartment model)
   12.11. A forward door, the bottom door loop
   12.12. Adjustment of a window and a bearing element of a door
   12.13. Window condensing stoppers, a window regulator
   12.14. The door lock
   12.15. Draught of lever transfer of the lock
   12.16. A rope of an internal door-lock
   12.17. A rotary clamp, an adjusting spring
   12.18. Adjustment of doors
   12.19. A bearing element of a door
   12.20. The central lock
   12.21. The pump with two modes of forcing
   12.22. The leading activator
   12.23. The activator of a back door
   12.24. The activator of a cover of a luggage carrier
   12.25. The activator of a cover of a fuel tank
   12.26. Door glass (Compartment model)
   12.27. Adjustment of a butt overlay (Compartment model)
   12.28. A skeleton of a back door, the bottom loop of a door
   12.29. A bearing element of the back door, a condensing stopper
   12.30. A rope, шарнирный the lever
   12.31. The door handle
   12.32. The holder of components of a door
   12.33. The hatch
   12.34. A bumper casing
   12.35. Hermetic sealing of a back bumper
   12.36. An extending clamp
   12.37. A forward spoiler / a lining of a niche of a wheel (Compartment model)
   12.38. The top overlay of a forward spoiler (Compartment model)
   12.39. A back spoiler / a lining of a niche of a wheel
   12.40. A back bumper (Compartment model)
   12.41. window raiser
   12.42. Internal furnish of a body
   12.43. Sitting
+ 13. A central air
+ 14. An electric equipment


32ad0625

12.14. The door lock
THE GENERAL DATA

Door-lock, draught of the lock in assemblage / the lock cylinder in assemblage


1. A lock control lever
2. Draught of lever transfer of the lock
At removal disconnect the lock
3. A control lever clip
4. A plastic washer
5. 16 Н.м.
6. A konusnaja washer
Two can be established конусные washers if it is necessary for adjustment
7. A bolt запорной door-lock plates, 50 Н.м.
8. The door lock
9. A rope, for work in a door
10. Clips, watch a direction of the main draught in a clip
11. A condensing lining
12. A fixing plate of draught of the lock
13. A rotary clamp
For removal зажиа to turn on 65 °
14. 3 Н.м.
15. The door handle
16. An external plate of the lock
17. Draught of lever transfer of the lock, the lock cylinder
Pay attention that draught is attached with the help шарнирной plugs

Door-lock
1. A bolt with a cylindrical head, 3 Н.м.
2. The door handle
3. The lock cylinder
Remove only by means of a key
4. A condensing ring
5. A plate
6. A spring
7. A control lever with the loose leaf
8. The S-shaped clamp
9. A lock clamp
For removal to turn on 65 °

Door-lock

Removal


PERFORMANCE ORDER
1) remove the decorative panel of a forward door
2) disconnect a clip of draught of lever transfer and extend draught
3) disconnect a rope
4) pull out a door-lock from knot 2
5) remove a lining 3

Installation

Installation carry out upside-down, in view of the following:

PERFORMANCE ORDER
1) again to connect a rope, pull the lever 4 in an arrow direction; insert a screw-driver into an aperture 5 to establish a rope into place
2) screw up all bolts with the moment 16 Н.м.

The door lock in assemblage (Compartment model)

1. An external plate of a door-lock
2. The door handle
3. A washer
4. A bolt with a head under a face key
5. Draught of the lock – the lock cylinder
At снятиии displace the rotary plug
6. A rope
7. Clips
Watch a direction of the main draught in a clip
8. Draught of the lock
9. The door lock
10. A screw with a crosswise head
11. A fixing plate of draught of the lock
12. A bolt, 16 Н.м.
13. A clamp
14. A clamp substrate
Can be established more than one
15. A condensing lining
16. A door-lock
17. The self-cutting screw with плоскоконической a head, 16 Н.м.
18. A clamp for a control lever
Press on муфту to remove draught of lever transfer of the lock
19. Draught of the lock
20. Draught of a control lever of the lock
21. The door-lock button
22. A rotary clamp

The door lock (Compartment model)

Removal


PERFORMANCE ORDER
1) remove the decorative panel of a forward door
2) disconnect a clip of draught of lever transfer and extend draught
3) disconnect a rope
4) pull out a door-lock from knot 2

Installation

Installation carry out upside-down, in view of the following:

PERFORMANCE ORDER
1) connect a rope, having pulled the lever 4 in a direction specified by an arrow
2) place a screw-driver in an aperture 5 to establish a rope into place
3) screw up all bolts with the moment 16 Н.м.

Door-lock cover, removal

PERFORMANCE ORDER
Disconnect a cover from a door covering

Door-lock cover, installation

Installation carry out upside-down.

Decorative covering of the handle of the lock, removal


The prevention

The decorative covering of the handle of a door should be removed before removal of the handle not to admit damage of the painted surface of a decorative covering.


PERFORMANCE ORDER
1) lift the door handle
2) pull out the lock probe in a direction specified by an arrow
3) remove a decorative covering

Door-lock (models of the Compartment since 1990 modelling years)

1. An adjusting detail
Squeezing the lever on a carving and it can be adjusted through a fixing aperture
2. A lock aperture
3. The door lock
4. 16 Н.м.
5. A plastic washer
6. A konusnaja washer
Two can be in case of need established конусные washers
7. A pin of a latch 50 Н.м.
8. A rope for the internal lock of a door
9. A clamp
Pay attention to position of a rope in clamps
10. A clamp
For a clamp detachment remove a rope and turn a clamp on 90 °
11. An extending clamp
12. The sharnirnyj lever
13. Draught of the lever mechanism
14. A condensing lining
15. A rope of the lock of a door
16. The door handle
17. An external covering of the handle of a door
18. 3 Н.м.

The door lock (models of the Compartment since 1990 modelling years)

Removal


PERFORMANCE ORDER
1) remove the decorative panel of a forward door
2) turn the lever 1, having pulled a rope in a direction specified by an arrow, and supporting in the necessary position by means of a screw-driver through an aperture 2
3) disconnect a rope
4) unscrew bolts
5) pull out the lock of a door from a clamp 3, sealants 5

Installation

Installation carry out upside-down, in view of the following:

PERFORMANCE ORDER
1) attach a rope
2) insert the door lock into a clamp
3) combine the handle of a door with the lock
4) adjust, as it is required
5) direct приводной the mechanism 4 in приводной the lever of the lock of a door; this operation can be observed through an aperture for access