Audi 80/90/Coupe

Since 1986-1991 of release

Repair and car operation



Audi 80/90/Coupe
+ 1.2. Car identification
+ 2. Engines, carburettors
3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. An exhaust system
+ 7. Ignition system
+ 8. Transmission
+ 9. Suspension brackets, wheels
+ 10. Brake system
+ 11. A steering
- 12. A body, salon
   12.2. The central section of a guard
   12.3. A cowl rope
   12.4. A forward guard
   12.5. A forward wing
   12.6. Lock pins of a cowl, the rubber shock-absorber
   12.7. A cowl
   12.8. A gazonapolnennaja rack (models the Sedan)
   12.9. A luggage carrier cover
   12.10. A back door (Compartment model)
   12.11. A forward door, the bottom door loop
   12.12. Adjustment of a window and a bearing element of a door
   12.13. Window condensing stoppers, a window regulator
   12.14. The door lock
   12.15. Draught of lever transfer of the lock
   12.16. A rope of an internal door-lock
   12.17. A rotary clamp, an adjusting spring
   12.18. Adjustment of doors
   12.19. A bearing element of a door
   12.20. The central lock
   12.21. The pump with two modes of forcing
   12.22. The leading activator
   12.23. The activator of a back door
   12.24. The activator of a cover of a luggage carrier
   12.25. The activator of a cover of a fuel tank
   12.26. Door glass (Compartment model)
   12.27. Adjustment of a butt overlay (Compartment model)
   12.28. A skeleton of a back door, the bottom loop of a door
   12.29. A bearing element of the back door, a condensing stopper
   12.30. A rope, шарнирный the lever
   12.31. The door handle
   12.32. The holder of components of a door
   12.33. The hatch
   12.34. A bumper casing
   12.35. Hermetic sealing of a back bumper
   12.36. An extending clamp
   12.37. A forward spoiler / a lining of a niche of a wheel (Compartment model)
   12.38. The top overlay of a forward spoiler (Compartment model)
   12.39. A back spoiler / a lining of a niche of a wheel
   12.40. A back bumper (Compartment model)
   12.41. window raiser
   12.42. Internal furnish of a body
   12.43. Sitting
+ 13. A central air
+ 14. An electric equipment


32ad0625

12.18. Adjustment of doors
THE GENERAL DATA

Adjust a backlash, displacing door loops

And = 5 + 1 mm

b = 5.5 + 1 mm

Level height with a case line

Adjustment place – loops (very big apertures on a loop in a place where it joins a forward / central rack of a body).

To avoid noise from air, regulate on assembly loops or in a back part of doors on a pin запорной plates.

Sections А–А, В–В, С–С:

With = 0.5 + 0.5 mm

Section D–D:

d = 14.5 mm

Door backlash, adjustment

PERFORMANCE ORDER
1) having unscrewed bolts 1, unscrew the plug with the cutting, being behind bolts until it will not cease to adjoin to a forward rack of a body
2) ослабьте bolts 2, close a door and adjust a backlash, moving a door
And = 5 + 1 mm
3) ослабьте or tighten by means of a wrench
4) screw up the plug with cutting until it will not contact with a forward rack of a body
5) screw up bolts and clamp them with the moment 30 Н.м.
6) check up a backlash

Height adjustment
PERFORMANCE ORDER
1) ослабьте bolts 1 and 2
2) ослабьте or tighten by means of a wrench
3) move door loops
4) tighten bolts; 30 Н.м.
5) ослабьте bolts (arrows), also displace a door in the necessary direction

6) tighten bolts; 30 Н.м.

Prevention of noise from a wind

1 – a screwed detail of carving connection

2 – a washer with чашеобразной dredging

3 – a washer


Two washers with чашеобразной dredging can be in case of need used.

PERFORMANCE ORDER
1) adjust a screwed detail of carving connection of a latch in a back part of a door
2) a screwed detail of carving connection 50 Н.м.

Doors, adjustment (Compartment model)

PERFORMANCE ORDER
1) adjust a door backlash, displacing door loops
2) establish door height (a body contour). Adjustment is made on loops (very big apertures on a loop in a place where the loop fastens to a forward rack of a body)
3) for prevention of occurrence of noise from a wind regulate assembly loops of a door or in a back part of a door on запорной to a plate
4) ослабьте bolts 2, 4 by means of a wrench
5) unscrew the plug with cutting on bolts 2 from a forward rack of a body
6) close a door and displace it for backlash adjustment
7) twist the plug with cutting 3 until will be contact to a forward rack of a body
8) screw up bolts and tighten them with the moment 30 Н.м.
9) once again check up a backlash

Height adjustment

PERFORMANCE ORDER
1) ослабьте bolts 2, 4 by means of a wrench
2) unscrew the plug with cutting on bolts 2 from a forward rack of a body
3) close a door
4) displace door loops
5) tighten bolts with the moment 40 Н.м.

Noise from a wind in a forward part of a door, prevention

PERFORMANCE ORDER
1) ослабьте bolts 1
2) displace a door as it is required
3) tighten bolts 30 Н.м.

Noise from a wind in запорной to a plate, prevention

PERFORMANCE ORDER
Adjust a clamp pin in a back part of a door

Pin of a clamp 16 Н.м.

1 – a clamp pin
2 – a shock plate
3 – a substrate

For achievement of exact adjustment can be established more than one

Door backlash, adjustment (models of the Compartment since 1990 modelling years)

PERFORMANCE ORDER
1) having unscrewed bolts 1, unscrew the plug with cutting until it will not cease to adjoin to the central rack of a body
2) ослабьте bolts 2, close a door and adjust a backlash, displacing a door
And = 5 + 1 mm
3) open a door and tighten bolts 2 with the moment 30 Н.м.

The prevention

Unscrew or screw up, using a key 2598.


4) twist plugs with a carving 3 until they will not adjoin to the central rack of a body
5) screw up bolts, 30 Н.м.
6) check up a backlash

Door height, adjustment

PERFORMANCE ORDER
1) ослабьте bolts 1 and 2

The prevention

Unscrew or screw up, using a key 2598.


2) displace door loops in very big apertures
3) tighten bolts with the moment 30 Н.м.

Noise from a wind, elimination

PERFORMANCE ORDER
1) ослабьте bolts of a forward door (arrow), displace a door in grooves of loops
2) distance between a skeleton of a door and the central rack of a body
d = 14.5 mm
3) tighten bolts with the moment 30 Н.м.

Back door, elimination of noise from a wind

1 – a shock washer

2 – a washer with чашеобразной dredging

Two washers with чашеобразной dredging can be in case of need established.

Adjustment of a pin of a clamp of the lock of a door allows to eliminate noise in a back part of a door.

PERFORMANCE ORDER
1) adjust a clamp pin
2) 50 Н.м.